A soft or spongy spot in the floor
For your property, most manufactured homes are decked in particleboard, which swells and loses its bond once it stays wet.
Homes and commercial properties
Maryland
Our water-damage team removes water and dries lightweight floors, walls, insulation, and underbelly materials commonly affected in mobile homes.
Signs to look for
In simple terms, if you notice any of these problems, call us before water has more time to spread into nearby materials.
For your property, most manufactured homes are decked in particleboard, which swells and loses its bond once it stays wet.
To keep the next step clear, panel walls are joined with battens over the seams instead of taped and painted like drywall.
For your property, vinyl covered gypsum panel walls sit directly on the decking, so they wick water upward from the floor.
In simple terms, the seam where two sections join is the most common water entry point on a multi section home.
Before cleanup moves forward, older homes with low slope metal roofs pond water at seams, vents and the edges.
In simple terms, the furnace and water heater generally share one interior closet sitting directly on the decking. To keep the next step clear, a slow drip there soaks the panel under an appliance nobody moves.
What happens
Our water-damage team adjusts the work to where the water reached, where the water went, and the materials that can be saved.
To keep the next step clear, we note the home's age, whether it is a single wide or a double wide, and what the deck and the walls are actually made of.
Before cleanup moves forward, particleboard decking that has swelled or lost its bond does not come back, and drying it longer will not change that.
To keep the next step clear, panel walls come apart at the battens and the bottom course, which lets us dry the wall cavity without wrecking the whole room.
Before cleanup moves forward, portable extractors and compact submersible pumps come through a 30 inch doorway and up a set of steps.
In simple terms, many manufactured homes run a 100 amp service, which limits how much drying equipment the home can actually carry.
For your property, water that reaches an in floor supply duct sits there and gets blown through every room.
Talk with our water-damage team
Share where the water came from, what rooms are wet, and what you can see right now.
What to expect
Here is how we generally handle mobile home water damage near Maryland.
Before cleanup moves forward, share the approximate age, whether it is a single wide or double wide, and where the water is showing.
Your callTo keep the next step clear, close the fixture valve, or the main at the lot pedestal if it is above ground and safe to reach.
+5 minutesIn simple terms, keep people and heavy furniture off any soft area, because wet particleboard loses strength as soon as possible.
+15 minutesBefore cleanup moves forward, we confirm the deck material, the wall panel type, the marriage line if there is one, and where the ducts run.
On arrivalBefore cleanup moves forward, water comes off hard flooring and out of carpet and padding, and contents get lifted and blocked. In simple terms, deeper water is pumped first.
First hours on siteIn simple terms, we tell you which decking sections, wall panels and cabinets are coming out and which are staying.
Same dayIn simple terms, equipment is placed and the amperage counted before anyone drives away, so your service is not overloaded overnight.
Before we leaveUnderstanding the cost
We explain in plain language the step-by-step cleanup plan and price before you approve the job. These examples show what may change the estimate.
| Common situation | What the estimate may include | Typical range |
|---|---|---|
| One room of a manufactured home, clean water, extraction plus three to four days of drying | National estimate. A supply line or fixture caught as soon as possible, with little or no decking replacement. | $900 to $2,500 |
| Most of a single wide affected, clean water | To keep the next step clear, national estimate. Before cleanup moves forward, includes extraction, padding removal, wall panel bottom course work and five to seven days of equipment. | $3,000 to $8,000 |
| Double wide with several rooms and decking replacement | To keep the next step clear, national estimate. In simple terms, water across the marriage line, two duct runs and significant decking and panel replacement. | $6,000 to $18,000 |
| Particleboard decking replacement, per square foot | In simple terms, national estimate for removing and replacing failed floor decking, before the finish flooring above it. | $3 to $10 |
| Wall panel replacement, per square foot | To keep the next step clear, national estimate for vinyl covered gypsum panel sections including batten work. In simple terms, older patterns may not be matchable. | $2 to $6 |
| Manufactured home work priced by affected area, clean water | National estimate. Handy once someone has measured the water-damaged area and given you a number. | $3 to $7 per square foot |
| Belly wrap drained, wet insulation out, underbelly repair coordinated | To keep the next step clear, national estimate. | $800 to $3,500 |
| After hours or overnight dispatch charge | To keep the next step clear, national estimate. In simple terms, one charge on the first visit, for nights, weekends and holidays. | $100 to $400 |
What the deck is made of
Particleboard decking that has swelled has to be replaced, and that is labor plus material plus flooring above it.
How much of the home is wet
To keep the next step clear, pricing follows affected square footage.
Single section or multi section
To keep the next step clear, a double wide is roughly twice the area and adds the marriage line as both a leak path and a drying boundary.
How clean the water was
Supply line water is the least damaging case and saves the most material.
Wall panel count
To keep the next step clear, panel replacement is priced by area and by how many batten lines have to be opened.
Duct involvement
For your property, clearing and drying in floor ducts is straightforward. In simple terms, replacing a collapsed or contaminated duct section, including a crossover duct, means working under the home.
Why timing matters
Water might keep moving into nearby materials even when the surface looks dry.
To keep the next step clear, once the panel swells and its bond fails, it stays swollen and weak no matter how long you dry it.
For your property, the vinyl film on these panels is effectively a vapor barrier on the room side, so moisture cannot escape toward the air you are drying.
In simple terms, small air volume means moisture saturates every room within hours, so there is no comfortable dry side to retreat to.
To keep the next step clear, standing water inside a supply duct or the crossover duct gets pushed through the home each time the system runs.
Helpful service information
Begin with the short explanation. Open a card if you want a little more detail.
Floors are generally decked in particleboard over relatively shallow floor joists, glued and stapled as a system.
Manufactured homes are built to the federal HUD Code, which produces a very different set of materials from a site built house.
For your property, that film behaves like a vapor barrier on the room side, so moisture in the gypsum core cannot escape toward the dry air you are creating in the room.
In simple terms, the vinyl face on a panel wall is the detail that catches inexperienced crews. For your property, that film behaves like a vapor barrier on the room side, so moisture in the gypsum core cannot escape toward the dry air you are creating in the room.
A single section home holds a fraction of the air a two story house does, so evaporating water pushes relative humidity up very as soon as possible and evaporation then stalls.
Air volume is the quiet variable in a home this size. A single section home holds a fraction of the air a two story house does, so evaporating water pushes relative humidity up very as soon as possible and evaporation then stalls.
Help near you
Pick your area below, or call (855) 704-3735 and describe what you are seeing.
You may also need
Our water-damage team removes water from homes, protects belongings, and dries affected rooms after leaks, overflows, storms, or appliance failures.
Get a Quote: (855) 704-3735Our water-damage team removes water beneath the home, clears wet debris or insulation, and dries joists, subflooring, and foundation areas.
Get a Quote: (855) 704-3735Our water-damage team removes surface water and dries moisture trapped beneath finished flooring to protect the subfloor and surrounding materials.
Get a Quote: (855) 704-3735Our water-damage team pumps out crawl-space water, removes wet debris or insulation, and dries framing to control moisture beneath the home.
Get a Quote: (855) 704-3735Our water-damage team removes water, damaged materials, and residue, then cleans and dries affected rooms so repair work might move forward.
Get a Quote: (855) 704-3735Our water-damage team finds moisture inside walls and uses targeted drying or controlled removal to protect framing and nearby finishes.
Get a Quote: (855) 704-3735Our water-damage team addresses water damage in rental properties with clear documentation, moisture readings, and coordinated cleanup for owners, managers, and tenants.
Get a Quote: (855) 704-3735Our water-damage team controls the source, removes water, protects contents, and stabilizes wet materials to prevent avoidable secondary damage.
Get a Quote: (855) 704-3735Common questions
For your property, it depends entirely on the deck material. In simple terms, most manufactured homes use particleboard decking, and once it has swelled or lost its bond it does not recover, so those sections come out.
Before cleanup moves forward, as a national estimate, one wet room with a few days of drying commonly runs $900 to $2,500.
In simple terms, three reasons. For your property, the decking is regularly particleboard rather than plywood, and the walls are vinyl faced gypsum panels joined with battens rather than taped drywall.
To keep the next step clear, the bottom few inches are generally the problem, because panels sit on the deck and wick water upward.
In simple terms, that is a separate work plan from the work inside your home, and our under house water removal page covers it in full.
To keep the next step clear, extraction generally finishes in one to three hours. In simple terms, drying then takes about three to five days for a typical loss, sometimes less because there is less material.
To keep the next step clear, yes, and it is one of the most commonly missed steps. To keep the next step clear, supply ducts run inside the floor and the crossover duct links the sections on a double wide, so water sits in them and gets blown through the home.
Talk with our water-damage team
Share where the water came from, what rooms are wet, and what you can see right now.
Areas we serve
Our water-damage team helps homes, businesses, and managed properties throughout Maryland and nearby communities.
View the area on Google Maps